Commit graph

880 commits

Author SHA1 Message Date
Jay Vosburgh
c2edacf80e bonding / ipv6: no addrconf for slaves separately from master
At present, when a device is enslaved to bonding, if ipv6 is
active then addrconf will be initated on the slave (because it is closed
then opened during the enslavement processing).  This causes DAD and RS
packets to be sent from the slave.  These packets in turn can confuse
switches that perform ipv6 snooping, causing them to incorrectly update
their forwarding tables (if, e.g., the slave being added is an inactve
backup that won't be used right away) and direct traffic away from the
active slave to a backup slave (where the incoming packets will be
dropped).

	This patch alters the behavior so that addrconf will only run on
the master device itself.  I believe this is logically correct, as it
prevents slaves from having an IPv6 identity independent from the
master.  This is consistent with the IPv4 behavior for bonding.

	This is accomplished by (a) having bonding set IFF_SLAVE sooner
in the enslavement processing than currently occurs (before open, not
after), and (b) having ipv6 addrconf ignore UP and CHANGE events on
slave devices.

	The eql driver also uses the IFF_SLAVE flag.  I inspected eql,
and I believe this change is reasonable for its usage of IFF_SLAVE, but
I did not test it.

Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-10 12:41:19 -04:00
YOSHIFUJI Hideaki
6d5b78cdd5 [IPV6] NDISC: Fix thinko to control Router Preference support.
Bug reported by Haruhito Watanabe <haruhito@sfc.keio.ac.jp>.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-06-22 16:07:04 -07:00
Herbert Xu
74235a25c6 [IPV6] addrconf: Fix IPv6 on tuntap tunnels
The recent patch that added ipv6_hwtype is broken on tuntap tunnels.
Indeed, it's broken on any device that does not pass the ipv6_hwtype
test.

The reason is that the original test only applies to autoconfiguration,
not IPv6 support.  IPv6 support is allowed on any device.  In fact,
even with the ipv6_hwtype patch applied you can still add IPv6 addresses
to any interface that doesn't pass thw ipv6_hwtype test provided that
they have a sufficiently large MTU.  This is a serious problem because
come deregistration time these devices won't be cleaned up properly.

I've gone back and looked at the rationale for the patch.  It appears
that the real problem is that we were creating IPv6 devices even if the
MTU was too small.  So here's a patch which fixes that and reverts the
ipv6_hwtype stuff.

Thanks to Kanru Chen for reporting this issue.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-06-14 13:02:55 -07:00
David S. Miller
3d7dbeac58 [TCP]: Disable TSO if MD5SIG is enabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-06-12 14:36:42 -07:00
David S. Miller
df2bc459a3 [UDP]: Revert 2-pass hashing changes.
This reverts changesets:

6aaf47fa48
b7b5f487ab
de34ed91c4
fc038410b4

There are still some correctness issues recently
discovered which do not have a known fix that doesn't
involve doing a full hash table scan on port bind.

So revert for now.

Signed-off-by: David S. Miller <davem@davemloft.net>
2007-06-07 13:40:50 -07:00
Patrick McHarrdy
3c158f7f57 [NETFILTER]: nf_conntrack: fix helper module unload races
When a helper module is unloaded all conntracks refering to it have their
helper pointer NULLed out, leading to lots of races. In most places this
can be fixed by proper use of RCU (they do already check for != NULL,
but in a racy way), additionally nf_conntrack_expect_related needs to
bail out when no helper is present.

Also remove two paranoid BUG_ONs in nf_conntrack_proto_gre that are racy
and not worth fixing.

Signed-off-by: Patrick McHarrdy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-06-07 13:40:26 -07:00
Patrick McHardy
ef7c79ed64 [NETLINK]: Mark netlink policies const
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-06-07 13:40:10 -07:00
Bill Nottingham
75202e7689 [NET]: Fix comparisons of unsigned < 0.
Recent gcc versions emit warnings when unsigned variables are
compared < 0 or >= 0.

Signed-off-by: Bill Nottingham <notting@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-06-03 18:08:47 -07:00
David S. Miller
8c7fc03e27 [IPV6]: Fix build warning.
net/ipv6/ip6_fib.c: In function ‘fib6_add_rt2node’:
net/ipv6/ip6_fib.c:661: warning: label ‘out’ defined but not used

Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-31 01:23:31 -07:00
Kazunori MIYAZAWA
f282d45cb4 [IPSEC]: Fix panic when using inter address familiy IPsec on loopback.
Signed-off-by: Kazunori MIYAZAWA <kazunori@miyazawa.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-31 01:23:28 -07:00
YOSHIFUJI Hideaki
7ebba6d14f [IPV6] ROUTE: No longer handle ::/0 specially.
We do not need to handle ::/0 routes specially any longer.
This should fix BUG #8349.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Yuji Sekiya <sekiya@wide.ad.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-31 01:23:26 -07:00
Kazunori MIYAZAWA
144466bdf8 [IPSEC]: Fix IPv6 AH calculation in outbound
Signed-off-by: Kazunori MIYAZAWA <miyazawa@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-31 01:23:25 -07:00
David S. Miller
14e50e57ae [XFRM]: Allow packet drops during larval state resolution.
The current IPSEC rule resolution behavior we have does not work for a
lot of people, even though technically it's an improvement from the
-EAGAIN buisness we had before.

Right now we'll block until the key manager resolves the route.  That
works for simple cases, but many folks would rather packets get
silently dropped until the key manager resolves the IPSEC rules.

We can't tell these folks to "set the socket non-blocking" because
they don't have control over the non-block setting of things like the
sockets used to resolve DNS deep inside of the resolver libraries in
libc.

With that in mind I coded up the patch below with some help from
Herbert Xu which provides packet-drop behavior during larval state
resolution, controllable via sysctl and off by default.

This lays the framework to either:

1) Make this default at some point or...

2) Move this logic into xfrm{4,6}_policy.c and implement the
   ARP-like resolution queue we've all been dreaming of.
   The idea would be to queue packets to the policy, then
   once the larval state is resolved by the key manager we
   re-resolve the route and push the packets out.  The
   packets would timeout if the rule didn't get resolved
   in a certain amount of time.

Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-24 18:17:54 -07:00
Oliver Hartkopp
bbb711e633 [IPV6]: Ignore ipv6 events on non-IPV6 capable devices.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-24 16:36:44 -07:00
Corey Mutter
ae7bf20a63 [IPV6]: Reverse sense of promisc tests in ip6_mc_input
Reverse the sense of the promiscuous-mode tests in ip6_mc_input(). 

Signed-off-by: Corey Mutter <crm-netdev@mutternet.com>
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-14 03:00:27 -07:00
Patrick McHardy
3c2ad469c3 [NETFILTER]: Clean up table initialization
- move arp_tables initial table structure definitions to arp_tables.h
  similar to ip_tables and ip6_tables

- use C99 initializers

- use initializer macros where possible

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-10 23:47:43 -07:00
David S. Miller
fc038410b4 [UDP]: Fix AF-specific references in AF-agnostic code.
__udp_lib_port_inuse() cannot make direct references to
inet_sk(sk)->rcv_saddr as that is ipv4 specific state and
this code is used by ipv6 too.

Use an operations vector to solve this, and this also paves
the way for ipv6 support for non-wild saddr hashing in UDP.

Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-10 23:47:22 -07:00
YOSHIFUJI Hideaki
9a6bf6fe71 [IPV6] ROUTE: Assign rt6i_idev for ip6_{prohibit,blk_hole}_entry.
I think this is less critical, but is also suitable for -stable
release.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-10 23:46:12 -07:00
YOSHIFUJI Hideaki
e76b2b2567 [IPV6]: Do no rely on skb->dst before it is assigned.
Because skb->dst is assigned in ip6_route_input(), it is really
bad to use it in hop-by-hop option handler(s).

Closes: Bug #8450 (Eric Sesterhenn <snakebyte@gmx.de>)
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-10 23:45:58 -07:00
David L Stevens
5bb1ab09e4 [IPV6]: Send ICMPv6 error on scope violations.
When an IPv6 router is forwarding a packet with a link-local scope source
address off-link, RFC 4007 requires it to send an ICMPv6 destination
unreachable with code 2 ("not neighbor"), but Linux doesn't. Fix below.

Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-10 23:45:32 -07:00
David Sterba
3dde6ad8fc Fix trivial typos in Kconfig* files
Fix several typos in help text in Kconfig* files.

Signed-off-by: David Sterba <dave@jikos.cz>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2007-05-09 07:12:20 +02:00
Randy Dunlap
e63340ae6b header cleaning: don't include smp_lock.h when not used
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.

Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-08 11:15:07 -07:00
Linus Torvalds
15700770ef Merge git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
  kconfig: fix mconf segmentation fault
  kbuild: enable use of code from a different dir
  kconfig: error out if recursive dependencies are found
  kbuild: scripts/basic/fixdep segfault on pathological string-o-death
  kconfig: correct minor typo in Kconfig warning message.
  kconfig: fix path to modules.txt in Kconfig help
  usr/Kconfig: fix typo
  kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
  kbuild: be more explicit on missing .config file
  kbuild: clarify the creation of the LOCALVERSION_AUTO string.
  kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
  kconfig: refer to qt3 if we cannot find qt libraries
  kbuild: handle compressed cpio initramfs-es
  kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
  kbuild: remove stale comment in modpost.c
  kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
  kbuild: fix make mrproper for Documentation/DocBook/man
  kbuild: remove kconfig binaries during make mrproper
  kconfig/menuconfig: do not hardcode '.config'
  kbuild: override build timestamp & version
  ...
2007-05-06 13:21:57 -07:00
Pavel Emelianov
7562f876cd [NET]: Rework dev_base via list_head (v3)
Cleanup of dev_base list use, with the aim to simplify making device
list per-namespace. In almost every occasion, use of dev_base variable
and dev->next pointer could be easily replaced by for_each_netdev
loop. A few most complicated places were converted to using
first_netdev()/next_netdev().

Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-05-03 15:13:45 -07:00
Alexander E. Patrakov
39f5fb3035 kconfig: fix path to modules.txt in Kconfig help
Documentation/modules.txt doesn't exist, but
Documentation/kbuild/modules.txt does.

Signed-off-by: Alexander E. Patrakov
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2007-05-02 20:58:11 +02:00
Eric Sesterhenn
d0772b70fa [IPV6]: Fix slab corruption running ip6sic
From: Eric Sesterhenn <snakebyte@gmx.de>

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-28 21:26:23 -07:00
Stephen Hemminger
5632c5152a [IPV6]: Track device renames in snmp6.
When network device's are renamed, the IPV6 snmp6 code
gets confused. It doesn't track name changes so it will OOPS
when network device's are removed.

The fix is trivial, just unregister/re-register in notify handler.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-28 21:16:39 -07:00
YOSHIFUJI Hideaki
ebbd90a730 [IPV6]: Fix thinko in ipv6_rthdr_rcv() changes.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-27 02:13:39 -07:00
Milind Arun Choudhary
4ef8d0aeaf [NET]: SPIN_LOCK_UNLOCKED cleanup in drivers/atm, net
SPIN_LOCK_UNLOCKED cleanup,use __SPIN_LOCK_UNLOCKED instead

Signed-off-by: Milind Arun Choudhary <milindchoudhary@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-26 01:37:44 -07:00
YOSHIFUJI Hideaki
e1ec7842df [IPV6] NDISC: Unify main process of sending ND messages.
Because ndisc_send_na(), ndisc_send_ns() and ndisc_send_rs()
are almost identical, so let's unify their common part.

With gcc (GCC) 3.3.5 (Debian 1:3.3.5-13) on i386,
	Before:
	   text	   data	    bss	    dec	    hex	filename
	  14689	    364	     24	  15077	   3ae5	net/ipv6/ndisc.o
	After:
	   text	   data	    bss	    dec	    hex	filename
	  12317	    364	     24	  12705	   31a1	net/ipv6/ndisc.o

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
2007-04-25 22:29:59 -07:00
YOSHIFUJI Hideaki
c53b3590bb [IPV6] XFRM: Use ip6addr_any where applicable.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
2007-04-25 22:29:58 -07:00
YOSHIFUJI Hideaki
df8981dc19 [IPV6]: Export in6addr_any for future use.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
2007-04-25 22:29:57 -07:00
YOSHIFUJI Hideaki
420fe234ad [IPV6] SIT: Unify code path to get hash array index.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
2007-04-25 22:29:54 -07:00
David S. Miller
30041e4af4 [IPV6]: Fix Makefile thinko.
obj-$(CONFIG_PROC_FS) --> ipv6-$(CONFIG_PROC_FS)

Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:53 -07:00
Herbert Xu
7f7d9a6b96 [IPV6]: Consolidate common SNMP code
This patch moves the non-proc SNMP code into addrconf.c and reuses
IPv4 SNMP code where applicable.

As a result we can skip proc.o if /proc is disabled.

Note that I've made a number of functions static since they're only
used by addrconf.c for now.  If they ever get used elsewhere we can
always remove the static.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:52 -07:00
YOSHIFUJI Hideaki
97fc8d0bc5 [IPV6] SNMP: Use put_unaligned() instead of memcpy().
Hint from David Miller <davem@davemloft.net>.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:37 -07:00
YOSHIFUJI Hideaki
952a10be32 [IPV6] SNMP: Fix several warnings without procfs.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
2007-04-25 22:29:36 -07:00
YOSHIFUJI Hideaki
2334e97355 [IPV6] SNMP: Avoid unaligned accesses.
Because stats pointer may not be aligned for u64, use memcpy
to fill u64 values.
Issue reported by David Miller <davem@davemloft.net>.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
2007-04-25 22:29:35 -07:00
Stephen Hemminger
3ff50b7997 [NET]: cleanup extra semicolons
Spring cleaning time...

There seems to be a lot of places in the network code that have
extra bogus semicolons after conditionals.  Most commonly is a
bogus semicolon after: switch() { }

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:24 -07:00
YOSHIFUJI Hideaki
1370b5a59b [IPV6] SNMP: Export statistics via netlink without CONFIG_PROC_FS.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:13 -07:00
YOSHIFUJI Hideaki
49ed67a9ee [IPV6] SNMP: Move some statistic bits to net/ipv6/proc.c.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:11 -07:00
YOSHIFUJI Hideaki
bf99f1bde3 [IPV6] SNMP: Netlink interface.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:10 -07:00
John Heffner
628a5c5618 [INET]: Add IP(V6)_PMTUDISC_RPOBE
Add IP(V6)_PMTUDISC_PROBE value for IP(V6)_MTU_DISCOVER.  This option forces
us not to fragment, but does not make use of the kernel path MTU discovery.
That is, it allows for user-mode MTU probing (or, packetization-layer path
MTU discovery).  This is particularly useful for diagnostic utilities, like
traceroute/tracepath.

Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:10 -07:00
John Heffner
b881ef7603 [IPV6]: MTU discovery check in ip6_fragment()
Adds a check in ip6_fragment() mirroring ip_fragment() for packets
that we can't fragment, and sends an ICMP Packet Too Big message
in response.

Signed-off-by: John Heffner <jheffner@psc.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:09 -07:00
Patrick McHardy
6313c1e099 [RTNETLINK]: Remove unnecessary locking in dump callbacks
Since we're now holding the rtnl during the entire dump operation, we can
remove additional locking for rtnl protected data. This patch does that
for all simple cases (dev_base_lock for dev_base walking, RCU protection
for FIB rule dumping).

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:05 -07:00
Patrick McHardy
af65bdfce9 [NETLINK]: Switch cb_lock spinlock to mutex and allow to override it
Switch cb_lock to mutex and allow netlink kernel users to override it
with a subsystem specific mutex for consistent locking in dump callbacks.
All netlink_dump_start users have been audited not to rely on any
side-effects of the previously used spinlock.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:03 -07:00
Patrick McHardy
3b5018d676 [NETFILTER]: {eb,ip6,ip}t_LOG: remove remains of LOG target overloading
All LOG targets always use their internal logging function nowadays, so
remove the incorrect error message and handle real errors (!= -EEXIST)
by failing to load.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:29:00 -07:00
Herbert Xu
604763722c [NET]: Treat CHECKSUM_PARTIAL as CHECKSUM_UNNECESSARY
When a transmitted packet is looped back directly, CHECKSUM_PARTIAL
maps to the semantics of CHECKSUM_UNNECESSARY.  Therefore we should
treat it as such in the stack.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:28:43 -07:00
Herbert Xu
663ead3bb8 [NET]: Use csum_start offset instead of skb_transport_header
The skb transport pointer is currently used to specify the start
of the checksum region for transmit checksum offload.  Unfortunately,
the same pointer is also used during receive side processing.

This creates a problem when we want to retransmit a received
packet with partial checksums since the skb transport pointer
would be overwritten.

This patch solves this problem by creating a new 16-bit csum_start
offset value to replace the skb transport header for the purpose
of checksums.  This offset is calculated from skb->head so that
it does not have to change when skb->data changes.

No extra space is required since csum_offset itself fits within
a 16-bit word so we can use the other 16 bits for csum_start.

For backwards compatibility, just before we push a packet with
partial checksums off into the device driver, we set the skb
transport header to what it would have been under the old scheme.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:28:40 -07:00
Patrick McHardy
c5c2523893 [XFRM]: Optimize MTU calculation
Replace the probing based MTU estimation, which usually takes 2-3 iterations
to find a fitting value and may underestimate the MTU, by an exact calculation.

Also fix underestimation of the XFRM trailer_len, which causes unnecessary
reallocations.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:28:38 -07:00
Patrick McHardy
557922584d [XFRM]: esp: fix skb_tail_pointer conversion bug
Fix incorrect switch of "trailer" skb by "skb" during skb_tail_pointer
conversion:

-       *(u8*)(trailer->tail - 1) = top_iph->protocol;
+       *(skb_tail_pointer(skb) - 1) = top_iph->protocol;

-       *(u8 *)(trailer->tail - 1) = *skb_network_header(skb);
+       *(skb_tail_pointer(skb) - 1) = *skb_network_header(skb);

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:28:37 -07:00
YOSHIFUJI Hideaki
29f6af7712 [IPV6] FIB6RULE: Find source address during looking up route.
When looking up route for destination with rules with
source address restrictions, we may need to find a source
address for the traffic if not given.

Based on patch from Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:28:35 -07:00
Arnaldo Carvalho de Melo
27d7ff46a3 [SK_BUFF]: Introduce skb_copy_to_linear_data{_offset}
To clearly state the intent of copying to linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.

Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
2007-04-25 22:28:29 -07:00
Arnaldo Carvalho de Melo
d626f62b11 [SK_BUFF]: Introduce skb_copy_from_linear_data{_offset}
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2007-04-25 22:28:23 -07:00
Herbert Xu
35fc92a9de [NET]: Allow forwarding of ip_summed except CHECKSUM_COMPLETE
Right now Xen has a horrible hack that lets it forward packets with
partial checksums.  One of the reasons that CHECKSUM_PARTIAL and
CHECKSUM_COMPLETE were added is so that we can get rid of this hack
(where it creates two extra bits in the skbuff to essentially mirror
ip_summed without being destroyed by the forwarding code).

I had forgotten that I've already gone through all the deivce drivers
last time around to make sure that they're looking at ip_summed ==
CHECKSUM_PARTIAL rather than ip_summed != 0 on transmit.  In any case,
I've now done that again so it should definitely be safe.

Unfortunately nobody has yet added any code to update CHECKSUM_COMPLETE
values on forward so we I'm setting that to CHECKSUM_NONE.  This should
be safe to remove for bridging but I'd like to check that code path
first.

So here is the patch that lets us get rid of the hack by preserving
ip_summed (mostly) on forwarded packets.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:28:16 -07:00
David S. Miller
b3da2cf37c [INET]: Use jhash + random secret for ehash.
The days are gone when this was not an issue, there are folks out
there with huge bot networks that can be used to attack the
established hash tables on remote systems.

So just like the routing cache and connection tracking
hash, use Jenkins hash with random secret input.

Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:28:06 -07:00
Patrick McHardy
e6f689db51 [NETFILTER]: Use setup_timer
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:27:43 -07:00
Patrick McHardy
1b53d9042c [NETFILTER]: Remove changelogs and CVS IDs
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:27:35 -07:00
Thomas Graf
c454673da7 [NET] rules: Unified rules dumping
Implements a unified, protocol independant rules dumping function
which is capable of both, dumping a specific protocol family or
all of them. This speeds up dumping as less lookups are required.

Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:27:17 -07:00
Thomas Graf
c127ea2c45 [IPv6]: Use rtnl registration interface
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:27:13 -07:00
Arnaldo Carvalho de Melo
6b88dd966b [SK_BUFF] ipv6: Use skb_network_offset in some more places
So that we reduce the number of direct accesses to skb->data.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
2007-04-25 22:26:38 -07:00
Arnaldo Carvalho de Melo
b529ccf279 [NETLINK]: Introduce nlmsg_hdr() helper
For the common "(struct nlmsghdr *)skb->data" sequence, so that we reduce the
number of direct accesses to skb->data and for consistency with all the other
cast skb member helpers.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:26:34 -07:00
Arnaldo Carvalho de Melo
27a884dc3c [SK_BUFF]: Convert skb->tail to sk_buff_data_t
So that it is also an offset from skb->head, reduces its size from 8 to 4 bytes
on 64bit architectures, allowing us to combine the 4 bytes hole left by the
layer headers conversion, reducing struct sk_buff size to 256 bytes, i.e. 4
64byte cachelines, and since the sk_buff slab cache is SLAB_HWCACHE_ALIGN...
:-)

Many calculations that previously required that skb->{transport,network,
mac}_header be first converted to a pointer now can be done directly, being
meaningful as offsets or pointers.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:26:28 -07:00
Arnaldo Carvalho de Melo
b0e380b1d8 [SK_BUFF]: unions of just one member don't get anything done, kill them
Renaming skb->h to skb->transport_header, skb->nh to skb->network_header and
skb->mac to skb->mac_header, to match the names of the associated helpers
(skb[_[re]set]_{transport,network,mac}_header).

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:26:20 -07:00
Arnaldo Carvalho de Melo
cfe1fc7759 [SK_BUFF]: Introduce skb_network_header_len
For the common sequence "skb->h.raw - skb->nh.raw", similar to skb->mac_len,
that is precalculated tho, don't think we need to bloat skb with one more
member, so just use this new helper, reducing the number of non-skbuff.h
references to the layer headers even more.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:26:19 -07:00
Arnaldo Carvalho de Melo
bff9b61ce3 [SK_BUFF]: Use the helpers to get the layer header pointer
Some more cases...

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:26:18 -07:00
Arnaldo Carvalho de Melo
ddc7b8e32b [SK_BUFF]: Some more layer header conversions
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:26:03 -07:00
Arnaldo Carvalho de Melo
d10ba34b00 [SK_BUFF]: More skb_put related skb_reset_transport_header
This time we have to set it to skb->tail that is not anymore equal to
skb->data, so we either add a new helper or just add the skb->tail - skb->data
offset, for now do the later.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:26:01 -07:00
Arnaldo Carvalho de Melo
55f79cc0c0 [IPV6]: Reset the network header in ip6_nd_hdr
ip6_nd_hdr is always called immediately after a alloc_skb + skb_reserve
sequence, i.e. when skb->tail is equal to skb->data, making it correct to use
skb_reset_network_header().

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:26:00 -07:00
Yasuyuki Kozakai
e7ac05f340 [NETFILTER]: nf_conntrack: add nf_copy() to safely copy members in skb
This unifies the codes to copy netfilter related datas. Before copying,
nf_copy() puts original members in destination skb.

Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:55 -07:00
Arnaldo Carvalho de Melo
9c70220b73 [SK_BUFF]: Introduce skb_transport_header(skb)
For the places where we need a pointer to the transport header, it is
still legal to touch skb->h.raw directly if just adding to,
subtracting from or setting it to another layer header.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:31 -07:00
Arnaldo Carvalho de Melo
bd82393ca2 [SK_BUFF]: More skb_reset_transport_header conversions
These are a bit more subtle, they are of this type:

-       skb->h.raw = payload;
        __skb_pull(skb, payload - skb->data);
+       skb_reset_transport_header(skb);

__skb_pull results in:

skb->data = skb->data + payload - skb->data;
skb->data = payload;

So after __skb_pull we have skb->data pointing to payload and we can
just call skb_reset_transport_header(skb), that will do:

skb->h.raw = payload;

The others are similar, allowing us to get rid of some more cases where a
pointer was being attributed to the layer headers.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:29 -07:00
Arnaldo Carvalho de Melo
39b89160df [SK_BUFF]: Introduce ipipv6_hdr(), remove skb->h.ipv6h
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:28 -07:00
Arnaldo Carvalho de Melo
b0061ce49c [SK_BUFF]: Introduce ipip_hdr(), remove skb->h.ipiph
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:27 -07:00
Arnaldo Carvalho de Melo
aa8223c7bb [SK_BUFF]: Introduce tcp_hdr(), remove skb->h.th
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:26 -07:00
Arnaldo Carvalho de Melo
ab6a5bb6b2 [TCP]: Introduce tcp_hdrlen() and tcp_optlen()
The ip_hdrlen() buddy, created to reduce the number of skb->h.th-> uses and to
avoid the longer, open coded equivalent.

Ditched a no-op in bnx2 in the process.

I wonder if we should have a BUG_ON(skb->h.th->doff < 5) in tcp_optlen()...

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:24 -07:00
Arnaldo Carvalho de Melo
88c7664f13 [SK_BUFF]: Introduce icmp_hdr(), remove skb->h.icmph
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:23 -07:00
Arnaldo Carvalho de Melo
4bedb45203 [SK_BUFF]: Introduce udp_hdr(), remove skb->h.uh
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:22 -07:00
Arnaldo Carvalho de Melo
cc70ab261c [ICMP6]: Introduce icmp6_hdr()
For consistency with all the other skb->h.raw accessors.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:20 -07:00
Arnaldo Carvalho de Melo
967b05f64e [SK_BUFF]: Introduce skb_set_transport_header
For the cases where the transport header is being set to a offset from
skb->data.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:17 -07:00
Arnaldo Carvalho de Melo
ea2ae17d64 [SK_BUFF]: Introduce skb_transport_offset()
For the quite common 'skb->h.raw - skb->data' sequence.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:16 -07:00
Arnaldo Carvalho de Melo
badff6d01a [SK_BUFF]: Introduce skb_reset_transport_header(skb)
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.

This one touches just the most simple cases:

skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()

The next ones will handle the slightly more "complex" cases.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:15 -07:00
Arnaldo Carvalho de Melo
0660e03f6b [SK_BUFF]: Introduce ipv6_hdr(), remove skb->nh.ipv6h
Now the skb->nh union has just one member, .raw, i.e. it is just like the
skb->mac union, strange, no? I'm just leaving it like that till the transport
layer is done with, when we'll rename skb->mac.raw to skb->mac_header (or
->mac_header_offset?), ditto for ->{h,nh}.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:14 -07:00
Arnaldo Carvalho de Melo
eddc9ec53b [SK_BUFF]: Introduce ip_hdr(), remove skb->nh.iph
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:10 -07:00
Arnaldo Carvalho de Melo
c9bdd4b525 [IP]: Introduce ip_hdrlen()
For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open
coded skb->nh.iph uses, now to go after the rest...

Just out of curiosity, here are the idioms found to get the same result:

skb->nh.iph->ihl << 2
skb->nh.iph->ihl<<2
skb->nh.iph->ihl * 4
skb->nh.iph->ihl*4
(skb->nh.iph)->ihl * sizeof(u32)

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:07 -07:00
Arnaldo Carvalho de Melo
c14d2450cb [SK_BUFF]: Introduce skb_set_network_header
For the cases where the network header is being set to a offset from skb->data.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:25:01 -07:00
Arnaldo Carvalho de Melo
d56f90a7c9 [SK_BUFF]: Introduce skb_network_header()
For the places where we need a pointer to the network header, it is still legal
to touch skb->nh.raw directly if just adding to, subtracting from or setting it
to another layer header.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:59 -07:00
Arnaldo Carvalho de Melo
bbe735e424 [SK_BUFF]: Introduce skb_network_offset()
For the quite common 'skb->nh.raw - skb->data' sequence.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:58 -07:00
Arnaldo Carvalho de Melo
1ced98e81d [SK_BUFF] ipv6: More skb_reset_network_header conversions related to skb_pull
Now related to this form:

skb->nh.ipv6h = (struct ipv6hdr *)skb_put(skb, length);

That, as the others, is done when skb->tail is still equal to skb->data, making
the conversion to skb_reset_network_header possible.

Also one more case equivalent to skb->nh.raw = skb->data, of this form:

iph = (struct ipv6hdr *)skb->data;
<SNIP>
skb->nh.ipv6h = iph;

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:54 -07:00
Arnaldo Carvalho de Melo
e2d1bca7e6 [SK_BUFF]: Use skb_reset_network_header in skb_push cases
skb_push updates and returns skb->data, so we can just call
skb_reset_network_header after the call to skb_push.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:47 -07:00
Arnaldo Carvalho de Melo
c1d2bbe1cd [SK_BUFF]: Introduce skb_reset_network_header(skb)
For the common, open coded 'skb->nh.raw = skb->data' operation, so that we can
later turn skb->nh.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.

This one touches just the most simple case, next will handle the slightly more
"complex" cases.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:46 -07:00
Arnaldo Carvalho de Melo
57effc70a5 [IPV6]: Use skb->nh.ipv6h instead of casting skb->nh.raw
nh.ipv6h is there exactly for this reason! Use it while it exists ;-)

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:45 -07:00
Arnaldo Carvalho de Melo
98e399f82a [SK_BUFF]: Introduce skb_mac_header()
For the places where we need a pointer to the mac header, it is still legal to
touch skb->mac.raw directly if just adding to, subtracting from or setting it
to another layer header.

This one also converts some more cases to skb_reset_mac_header() that my
regex missed as it had no spaces before nor after '=', ugh.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:41 -07:00
Arnaldo Carvalho de Melo
39f69c6f92 [SK_BUFF] xfrm: Use skb_set_mac_header in the memmove cases
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:37 -07:00
Arnaldo Carvalho de Melo
459a98ed88 [SK_BUFF]: Introduce skb_reset_mac_header(skb)
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.

This one touches just the most simple case, next will handle the slightly more
"complex" cases.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:32 -07:00
YOSHIFUJI Hideaki
e5268f12f2 [IPV6]: Ensure to truncate result and return full length for sticky options.
Bug noticed by Chris Wright <chrisw@sous-sol.org>.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:17 -07:00
YOSHIFUJI Hideaki
4c6510a738 [IPV6]: Return correct result for sticky options.
We returned incorrect result with IPV6_RTHDRDSTOPTS, IPV6_RTHDR and
IPV6_DSTOPTS.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:16 -07:00
Stephen Hemminger
add459aa1a [UDP]: ipv6 style cleanup
Fix whitespace around keywords. Eliminate unnecessary ()'s on return
statements.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:08 -07:00
Eric Dumazet
ae40eb1ef3 [NET]: Introduce SIOCGSTAMPNS ioctl to get timestamps with nanosec resolution
Now network timestamps use ktime_t infrastructure, we can add a new
ioctl() SIOCGSTAMPNS command to get timestamps in 'struct timespec'.
User programs can thus access to nanosecond resolution.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
CC: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:04 -07:00
Herbert Xu
759e5d0064 [UDP]: Clean up UDP-Lite receive checksum
This patch eliminates some duplicate code for the verification of
receive checksums between UDP-Lite and UDP.  It does this by
introducing __skb_checksum_complete_head which is identical to
__skb_checksum_complete_head apart from the fact that it takes
a length parameter rather than computing the first skb->len bytes.

As a result UDP-Lite will be able to use hardware checksum offload
for packets which do not use partial coverage checksums.  It also
means that UDP-Lite loopback no longer does unnecessary checksum
verification.

If any NICs start support UDP-Lite this would also start working
automatically.

This patch removes the assumption that msg_flags has MSG_TRUNC clear
upon entry in recvmsg.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:23:51 -07:00