We should modify TIRs explicitly to apply the new RSS configuration.
The light ndo close/open calls do not "refresh" them.
Fixes: 2d75b2bc8a ('net/mlx5e: Add ethtool RSS configuration options')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Readers/Writers lock for SW timecounter was acquired without disabling
interrupts on local CPU.
The problematic scenario:
* HW timestamping is enabled
* Timestamp overflow periodic service task is running on local CPU and
holding write_lock for SW timecounter
* Completion arrives, triggers interrupt for local CPU.
Interrupt routine calls napi_schedule(), which triggers rx/tx
skb process.
An attempt to read SW timecounter using read_lock is done, which is
already locked by a writer on the same CPU and cause soft lockup.
Add irqsave/irqrestore for when using the readers/writers lock for
writing.
Fixes: ef9814deaf ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool LRO enable/disable is broken, as of today we only modify TCP
TIRs in order to apply the requested configuration.
Hardware requires that all TIRs pointing to the same RQ should share the
same LRO configuration. For that all other TIRs' LRO fields must be
modified as well.
Fixes: 5c50368f38 ('net/mlx5e: Light-weight netdev open/stop')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the MLX5E_CQ_HAS_CQES optimization flag, the following buggy
flow might occur:
- Suppose RX is always busy, TX has a single packet every second.
- We poll a single TX cqe and clear its flag.
- We never arm it again as RX is always busy.
- TX CQ flag is never changed, and new TX cqes are not polled.
We revert this optimization.
Fixes: e586b3b0ba ('net/mlx5: Ethernet Datapath files')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8168G/RTL8168H/RTL8411B/RTL8107E, enable this flag to eliminate
message "AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x0002
address=0x0000000000003000 flags=0x0050] in dmesg.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* check GCMP encryption vs. fragmentation properly; we'd found
this problem quite a while ago but waited for the 802.11 spec
to be updated
* fix RTS/CTS logic in minstrel_ht
* fix RX of certain public action frames in AP mode
* add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps
the kbuild robot pick up the right tree for it
-----BEGIN PGP SIGNATURE-----
iQIcBAABCgAGBQJW1u7EAAoJEGt7eEactAAdZXsP/il3dCxYtqYtBOzmR8OkDztn
yJiapt9aZ/u1a1mfDKfsJ2/8OLsE4pY/fp3G8TttURKNB/26sHWUEYSHWV2Ecfmi
4QFvAiUeO9Ue50ggASno239hp51KIKGcVF5flqKrCjTaSSyUm8YR78S1NlH2N+lT
i+i/AidHEdLnTgvYGOUhWu3QyL7Bm5t5wVZPivZUs0Zoos+tTokEj40eYmetQX27
lQMGa/xbvLHYeBcuLSgdQbzUR1jzOi70b9+QkjqhrYrlsc+MZE8ghwOgeAeQx56B
0sg0fZZVI8DIaCD5S3Pj8EP0WnP990DtM+4nSvtfFUYJxEM7LthEV+bs4Gr1MR2q
dZESMisKoRWBf2SyUhoVeUO6bV5kY+eTz/wyQCTdFsp9u6jzOgiY7y2aliqbJFgD
0Ydbyqq1dAeRqFaTg/46OAXkUxHW7/8hQC78Cmintevd1nHivZC3eevG6xj22G1N
eUvqy+OIv0d2Hg8+CL6oBsexQrKLg4bQFPR6s/doPnXtgsh5JccFYWujClsrNL26
kRb1kYrIqoVWXwnPp1dLF02s6Ny0+AW4xHLQIAwz5HACsJp+SjnpRP3WF9FTPs3V
T71dXQ48MLrQ/EVidCpMwJYoUnZ+BWeUf5hHpkxILIP1f0elx3i50eshlMNA/kwb
YzufoqiQhICciwEBAgBM
=2rZC
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-03-02' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are a few more fixes for the current cycle:
* check GCMP encryption vs. fragmentation properly; we'd found
this problem quite a while ago but waited for the 802.11 spec
to be updated
* fix RTS/CTS logic in minstrel_ht
* fix RX of certain public action frames in AP mode
* add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps
the kbuild robot pick up the right tree for it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt says:
====================
bnx2x: endianness fixes
this fixes a VLAN crash and some SRIOV bugs in bnx2x observed on ppc64.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with other event data structs and to lessen
the chance of a mistake should one of the reserved fields become
used in the future, define the reserved fields as little-endian.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were no missing endianness conversions in this case, but the
fields of struct cfc_del_event_data should be defined as little-endian
to get rid of the ugly (__force __le32) casts.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not really a bug, but it was odd that bnx2x_eq_int() read the
message data as if it were a cfc_del_event regardless of the event type.
It's cleaner to access only the appropriate member of union event_data
after checking the event opcode.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ppc64 the PF did not receive messages from VFs correctly.
Fields of struct vf_pf_event_data are little-endian.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF is sending a message to the PF, it needs to trigger the PF
to tell it the message is ready.
The trigger did not work on ppc64. No interrupt appeared in the PF.
The bug is due to confusion about the layout of struct trigger_vf_zone.
In bnx2x_send_msg2pf() the trigger is written using writeb(), not
writel(), so the attempt to define the struct with a reversed layout on
big-endian is counter-productive.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x crashes during the initialization of the 8021q module on ppc64.
The bug is a missing conversion from le32 in
bnx2x_handle_classification_eqe() when obtaining the cid value from
struct eth_event_data.
The fields in struct eth_event_data should all be declared as
little-endian and conversions added where missing.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since I maintain this driver as part of mac80211, add it to
the file list for mac80211; this helps submitters send it to
me instead of Kalle and also makes the build robot apply the
patches for it on the right tree for build attempts.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 'flags' parameter of the of_phy_connect() function wasn't described
in the kernel-doc comment...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_remaddr_seq_show(), we use variable *tsp to get the param *v.
but *tsp is also used to traversal transport_addr_list, which will cover
the previous value, and make sctp_transport_put work on the wrong transport.
So fix it by adding a new variable to get the param *v.
Fixes: fba4c330c5 ("sctp: hold transport before we access t->asoc in sctp proc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the member .cmp_addr of sctp_af_inet6, sctp_v6_cmp_addr should also check
the port of addresses, just like sctp_v4_cmp_addr, cause it's invoked by
sctp_cmp_addr_exact().
Now sctp_v6_cmp_addr just check the port when two addresses have different
family, and lack the port check for two ipv6 addresses. that will make
sctp_hash_cmp() cannot work well.
so fix it by adding ports comparison in sctp_v6_cmp_addr().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre Belloni says:
====================
phy: micrel: fix issues with interrupt on atmel boards
Since the phy is not polled anymore, there were issues getting a link on the
sama5d* xplained boards.
I'm not too sure about were those fixes should go and I'm wondering whether the
first one shoud be made generic.
For the second one, I found the PHY_HAS_MAGICANEG flag that is not used and I
wondering whether this is related to that kind of issue. I had a quick look at
the history and could'nt find its use.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable auto negotiation on init to properly detect an already plugged
cable at boot.
At boot, when the phy is started, it is in the PHY_UP state.
However, if a cable is plugged at boot, because auto negociation is already
enabled at the time we get the first interrupt, the phy is already running.
But the state machine then switches from PHY_UP to PHY_AN and calls
phy_start_aneg(). phy_start_aneg() will not do anything because aneg is
already enabled on the phy. It will then wait for a interrupt before going
further. This interrupt will never happen unless the cable is unplugged and
then replugged.
It was working properly before 321beec504 (net: phy: Use interrupts when
available in NOLINK state) because switching to NOLINK meant starting
polling the phy, even if IRQ were enabled.
Fixes: 321beec504 (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on ksz8081, when getting back from power down, interrupts are
disabled. ensure they are reenabled if they were previously enabled.
This fixes resuming which is failing on the xplained boards from atmel
since 321beec504 (net: phy: Use interrupts when available in NOLINK
state)
Fixes: 321beec504 (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ppp_read() and ppp_poll() can be called concurrently with ppp_ioctl().
In this case, ppp_ioctl() might call ppp_ccp_closed(), which may update
ppp->flags while ppp_read() or ppp_poll() is reading it.
The update done by ppp_ccp_closed() isn't atomic due to the bit mask
operation ('ppp->flags &= ~(SC_CCP_OPEN | SC_CCP_UP)'), so concurrent
readers might get transient values.
Reading incorrect ppp->flags may disturb the 'ppp->flags & SC_LOOP_TRAFFIC'
test in ppp_read() and ppp_poll(), which in turn can lead to improper
decision on whether the PPP unit file is ready for reading or not.
Since ppp_ccp_closed() is protected by the Rx and Tx locks (with
ppp_lock()), taking the Rx lock is enough for ppp_read() and ppp_poll()
to guarantee that ppp_ccp_closed() won't update ppp->flags
concurrently.
The same reasoning applies to ppp->n_channels. The 'n_channels' field
can also be written to concurrently by ppp_ioctl() (through
ppp_connect_channel() or ppp_disconnect_channel()). These writes aren't
atomic (simple increment/decrement), but are protected by both the Rx
and Tx locks (like in the ppp->flags case). So holding the Rx lock
before reading ppp->n_channels also prevents concurrent writes.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use list_move_tail() to move MAC address entry from list of pending
to list of active entries. Simple list_add_tail() leaves the entry
also in the first list, this leads to list corruption.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJW0ACIAAoJED07qiWsqSVqraYIALM+0BeB5V2g2kyjvsQS2Zah
1139UfEwVvb3djUhEvq68+zsXwPVrBdf2Kk8KgQxOzB3ctKRp8JtN7HPLWLXrgLw
WSFRhye/xUuPrUgiuwZ8cGR1QiBAuA/xRgFR8re7+pQ2nEzlx53neWolnjuesuWo
5MKoyPK7LSIgkZD7VteJklpScDQDqGcbc6w6pe1yg8gwQZoDycD1+Hqj4JKehqJN
J0W6puBL6urs9KtCzZRzMzEk09rH5BanQsAlCf4NkE0zvnPmtjptmsgRAo4rpAz3
6L6C+B1gph04eb+dXKsIRAVdN+kCHt1Sa7PlmfxXrY2hgVLvb+pXwJ6p3O6DRXE=
=L95V
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.5-20160226' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-02-26
this is a pull request of one patch for net.
The patch by Maximilain Schneider fixes a kfree() problem during disconnect in
the gs_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
RTS/CTS needs to be enabled if the rate is a fallback rate *or* if it's
a dual-stream rate and the sta is in dynamic SMPS mode.
Cc: stable@vger.kernel.org
Fixes: a3ebb4e1b7 ("mac80211: minstrel_ht: handle peers in dynamic SMPS")
Reported-by: Matías Richart <mrichart@fing.edu.uy>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Public Action frames use special rules for how the BSSID field (Address
3) is set. A wildcard BSSID is used in cases where the transmitter and
recipient are not members of the same BSS. As such, we need to accept
Public Action frames with wildcard BSSID.
Commit db8e173245 ("mac80211: ignore frames between TDLS peers when
operating as AP") added a rule that drops Action frames to TDLS-peers
based on an Action frame having different DA (Address 1) and BSSID
(Address 3) values. This is not correct since it misses the possibility
of BSSID being a wildcard BSSID in which case the Address 1 would not
necessarily match.
Fix this by allowing mac80211 to accept wildcard BSSID in an Action
frame when in AP mode.
Fixes: db8e173245 ("mac80211: ignore frames between TDLS peers when operating as AP")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recently, I fixed a bug in 3c59x:
commit 6e144419e4
Author: Neil Horman <nhorman@tuxdriver.com>
Date: Wed Jan 13 12:43:54 2016 -0500
3c59x: fix another page map/single unmap imbalance
Which correctly rebalanced dma mapping and unmapping types. Unfortunately it
introduced a new bug which causes oopses on older systems.
When mapping dma regions, the last entry for a packet in the 3c59x tx ring
encodes a LAST_FRAG bit, which is encoded as the high order bit of the buffers
length field. When it is unmapped the LAST_FRAG bit is cleared prior to being
passed to the unmap function. Unfortunately the commit above fails to do that
masking. It was missed in testing because the system on which I tested it had
an intel iommu, the driver for which ignores the size field, using only the DMA
address as the token to identify the mapping to be released. However, on older
systems that rely on swiotlb (or other dma drivers that key off that length
field), not masking off that LAST_FRAG high order bit results in parsing a huge
size to be release, leading to all sorts of odd corruptions and the like.
Fix is easy, just mask the length with 0xFFF. It should really be
&(LAST_FRAG-1), but 0xFFF is the style of the file, and I'd like to make this
fix minimal and correct before making it prettier.
Appies to the net tree cleanly. All testing on both iommu and swiommu based
systems produce good results
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the send skbuff reaches the end, nlmsg_put and friends returns
-EMSGSIZE but it is silently thrown away in ndo_fdb_dump. It is called
within a for_each_netdev loop and the first fdb entry of a following
netdev could fit in the remaining skbuff. This breaks the mechanism
of cb->args[0] and idx to keep track of the entries that are already
dumped, which results missing entries in bridge fdb show command.
Signed-off-by: Minoura Makoto <minoura@valinux.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
gs_destroy_candev() erroneously calls kfree() on a struct gs_can *, which is
allocated through alloc_candev() and should instead be freed using
free_candev() alone.
The inappropriate use of kfree() causes the kernel to hang when
gs_destroy_candev() is called.
Only the struct gs_usb * which is allocated through kzalloc() should be freed
using kfree() when the device is disconnected.
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On Thunderx pass 1.x and pass2 due to a HW errata default CQ
DROP_LEVEL of 0x80 is not sufficient to avoid CQ_WR_FULL Qset
error when packets are being received at >20Mpps resulting in
complete stall of packet reception.
This patch will configure it to 0x100 which is what is expected
by HW on Thunderx. On future passes of thunderx and other chips
HW default/reset value will be 0x100 or higher hence not overwritten.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There will be a log spam when there is no cable plugged. Please refer to
following links. https://bugzilla.kernel.org/show_bug.cgi?id=104351https://bugzilla.kernel.org/show_bug.cgi?id=107421
This issue is caused by runtime power management. When there is no cable
plugged, the driver will be suspend (runtime suspend) by OS and NIC will be
put into the D3 state. During this time, if OS call rtl8169_get_stats64()
to dump tally counter, because NIC is in D3 state, the register value read
by driver will return all 0xff. This will let driver think tally counter
flag is not toggled and then sends the warning message "rtl_counters_cond
== 1 (loop: 1000, delay: 10)" to kernel log.
For fixing this issue, 1.add checking driver's pm runtime status in
rtl8169_get_stats64(). 2.dump tally counter before going runtime suspend
for counter accuracy in runtime suspend.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to update the skb->csum after pulling the skb, otherwise
an unnecessary checksum (re)computation can ocure for IGMP/MLD packets
in the bridge code. Additionally this fixes the following splats for
network devices / bridge ports with support for and enabled RX checksum
offloading:
[...]
[ 43.986968] eth0: hw csum failure
[ 43.990344] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.4.0 #2
[ 43.996193] Hardware name: BCM2709
[ 43.999647] [<800204e0>] (unwind_backtrace) from [<8001cf14>] (show_stack+0x10/0x14)
[ 44.007432] [<8001cf14>] (show_stack) from [<801ab614>] (dump_stack+0x80/0x90)
[ 44.014695] [<801ab614>] (dump_stack) from [<802e4548>] (__skb_checksum_complete+0x6c/0xac)
[ 44.023090] [<802e4548>] (__skb_checksum_complete) from [<803a055c>] (ipv6_mc_validate_checksum+0x104/0x178)
[ 44.032959] [<803a055c>] (ipv6_mc_validate_checksum) from [<802e111c>] (skb_checksum_trimmed+0x130/0x188)
[ 44.042565] [<802e111c>] (skb_checksum_trimmed) from [<803a06e8>] (ipv6_mc_check_mld+0x118/0x338)
[ 44.051501] [<803a06e8>] (ipv6_mc_check_mld) from [<803b2c98>] (br_multicast_rcv+0x5dc/0xd00)
[ 44.060077] [<803b2c98>] (br_multicast_rcv) from [<803aa510>] (br_handle_frame_finish+0xac/0x51c)
[...]
Fixes: 9afd85c9e4 ("net: Export IGMP/MLD message validation code")
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by
qca_spi as it modifies the skb on xmit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qcaspi_netdev_setup accidentally clears IFF_BROADCAST.
So fix this by keeping the flags from ether_setup.
Reported-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>
Nik pointed that the VRF driver should be using skb_header_pointer
instead of accessing skb->data and bits beyond directly which can
be garbage.
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The JMC260 network card fails to suspend/resume because the call to
jme_start_irq() was too early, moving the call to jme_start_irq() after
the call to jme_reset_link() makes it work.
Prior this change suspend/resume would fail unless /sys/power/pm_async=0
was explicitly specified.
Relevant bug report: https://bugzilla.kernel.org/show_bug.cgi?id=112351
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* stop critical protocol session on disconnect to avoid
it getting stuck
* wext: fix two RTNL message ordering issues
* fix an uninitialized value (found by KASAN)
* fix an out-of-bounds access (also found by KASAN)
* clear connection keys when freeing them in all cases
(IBSS, all other places already did so)
* fix expected throughput unit to get consistent values
* set default TX aggregation timeout to 0 in minstrel
to avoid (really just hide) issues and perform better
-----BEGIN PGP SIGNATURE-----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=01n9
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Another small set of fixes:
* stop critical protocol session on disconnect to avoid
it getting stuck
* wext: fix two RTNL message ordering issues
* fix an uninitialized value (found by KASAN)
* fix an out-of-bounds access (also found by KASAN)
* clear connection keys when freeing them in all cases
(IBSS, all other places already did so)
* fix expected throughput unit to get consistent values
* set default TX aggregation timeout to 0 in minstrel
to avoid (really just hide) issues and perform better
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The fix in 35e2d1152b ("tunnels: Allow IPv6 UDP checksums to be correctly
controlled.") changed behavior for bpf_set_tunnel_key() when in use with
IPv6 and thus uncovered a bug that TUNNEL_CSUM needed to be set but wasn't.
As a result, the stack dropped ingress vxlan IPv6 packets, that have been
sent via eBPF through collect meta data mode due to checksum now being zero.
Since after LCO, we enable IPv4 checksum by default, so make that analogous
and only provide a flag BPF_F_ZERO_CSUM_TX for the user to turn it off in
IPv4 case.
Fixes: 35e2d1152b ("tunnels: Allow IPv6 UDP checksums to be correctly controlled.")
Fixes: c6c3345407 ("bpf: support ipv6 for bpf_skb_{set,get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we break the contract with GSO to only pass CHECKSUM_PARTIAL
skbs down. This can easily happen with UDP+IPv4 sockets with the first
MSG_MORE write smaller than the MTU, second write is a sendfile.
Returning -EOPNOTSUPP lets the callers fall back into normal sendmsg path,
were we calculate the checksum manually during copying.
Commit d749c9cbff ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked
sockets") started to exposes this bug.
Fixes: d749c9cbff ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked sockets")
Reported-by: Jiri Benc <jbenc@redhat.com>
Cc: Jiri Benc <jbenc@redhat.com>
Reported-by: Wakko Warner <wakko@animx.eu.org>
Cc: Wakko Warner <wakko@animx.eu.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some circumstances, e.g. when connecting to a switch, the ethernet
port will not be connected to a PHY. In that case a "fixed-link" DT node
can be used to replace it.
https://stackoverflow.com/questions/31046172/device-tree-for-phy-less-connection-to-a-dsa-switch
This patch adds support for the "fixed-link" node to the nb8800 driver.
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Acked-by: Mans Rullgard <mans@mansr.com>
Cc: Mason <slash.tmp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arithmetic to zero pad the last 64-bit word in the push buffer is not
correct.
1. It should be pdata + length to get to the end.
2. 'pdata' is void pointer and passing it to PTR_ALIGN() will cast the
aligned pointer to void. Pass 'end' which is u64 pointer to PTR_ALIGN()
instead so that the aligned pointer - 1 is the last 64-bit pointer to data.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPCB may contain data from previous layers (in the observed case the
qdisc layer). In the observed scenario, the data was misinterpreted as
ip header options, which later caused the ihl to be set to an invalid
value (<5). This resulted in an infinite loop in the mips implementation
of ip_fast_csum.
This patch clears IPCB(skb)->opt before dst_link_failure can be called for
various types of tunnels. This change only applies to encapsulated ipv4
packets.
The code introduced in 11c21a30 which clears all of IPCB has been removed
to be consistent with these changes, and instead the opt field is cleared
unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to
SIT, GRE, and IPIP tunnels.
The relevant vti, l2tp, and pptp functions already contain similar code for
clearing the IPCB.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it's converted into msecs, thus HZ=1000 intact.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: 740b0f1841 ("tcp: switch rtt estimations to usec resolution")
Signed-off-by: David S. Miller <davem@davemloft.net>
When user-space has started a critical protocol session and a disconnect
event occurs, the rdev::crit_prot_nlportid remains set. This caused a
subsequent NL80211_CMD_CRIT_PROTO_START to fail (-EBUSY). Fix this by
clearing the rdev attribute and call .crit_proto_stop() callback upon
disconnect event.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The connection keys are zeroed out in all other cases except this
one. Let's fix the last one as well.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.
Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.
Cc: stable@vger.kernel.org
Acked-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking fixes from David Miller:
"Looks like a lot, but mostly driver fixes scattered all over as usual.
Of note:
1) Add conditional sched in nf conntrack in cleanup to avoid NMI
watchdogs. From Florian Westphal.
2) Fix deadlock in nfnetlink cttimeout, also from Floarian.
3) Fix handling of slaves in bonding ARP monitor validation, from Jay
Vosburgh.
4) Callers of ip_cmsg_send() are responsible for freeing IP options,
some were not doing so. Fix from Eric Dumazet.
5) Fix per-cpu bugs in mvneta driver, from Gregory CLEMENT.
6) Fix vlan handling in mv88e6xxx DSA driver, from Vivien Didelot.
7) bcm7xxx PHY driver bug fixes from Florian Fainelli.
8) Avoid unaligned accesses to protocol headers wrt. GRE, from
Alexander Duyck.
9) SKB leaks and other problems in arc_emac driver, from Alexander
Kochetkov.
10) tcp_v4_inbound_md5_hash() releases listener socket instead of
request socket on error path, oops. Fix from Eric Dumazet.
11) Missing socket release in pppoe_rcv_core() that seems to have
existed basically forever. From Guillaume Nault.
12) Missing slave_dev unregister in dsa_slave_create() error path,
from Florian Fainelli.
13) crypto_alloc_hash() never returns NULL, fix return value check in
__tcp_alloc_md5sig_pool. From Insu Yun.
14) Properly expire exception route entries in ipv4, from Xin Long.
15) Fix races in tcp/dccp listener socket dismantle, from Eric
Dumazet.
16) Don't set IFF_TX_SKB_SHARING in vxlan, geneve, or GRE, it's not
legal. These drivers modify the SKB on transmit. From Jiri Benc.
17) Fix regression in the initialziation of netdev->tx_queue_len.
From Phil Sutter.
18) Missing unlock in tipc_nl_add_bc_link() error path, from Insu Yun.
19) SCTP port hash sizing does not properly ensure that table is a
power of two in size. From Neil Horman.
20) Fix initializing of software copy of MAC address in fmvj18x_cs
driver, from Ken Kawasaki"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (129 commits)
bnx2x: Fix 84833 phy command handler
bnx2x: Fix led setting for 84858 phy.
bnx2x: Correct 84858 PHY fw version
bnx2x: Fix 84833 RX CRC
bnx2x: Fix link-forcing for KR2
net: ethernet: davicom: fix devicetree irq resource
fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address
Driver: Vmxnet3: Update Rx ring 2 max size
net: netcp: rework the code for get/set sw_data in dma desc
soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
net: ti: netcp: restore get/set_pad_info() functionality
MAINTAINERS: Drop myself as xen netback maintainer
sctp: Fix port hash table size computation
can: ems_usb: Fix possible tx overflow
Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
net: bcmgenet: Fix internal PHY link state
af_unix: Don't use continue to re-execute unix_stream_read_generic loop
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
bnxt_en: Failure to update PHY is not fatal condition.
bnxt_en: Remove unnecessary call to update PHY settings.
...
Remove an un-necessary speed_index lookup for thermal hook in the gpio-fan
driver. The unnecessary speed lookup can hog the system.
Handle negative conversion values correctly in the ads1015 driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=luAI
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Two fixes headed for stable:
- Remove an unnecessary speed_index lookup for thermal hook in the
gpio-fan driver. The unnecessary speed lookup can hog the system.
- Handle negative conversion values correctly in the ads1015 driver"
* tag 'hwmon-for-linus-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gpio-fan) Remove un-necessary speed_index lookup for thermal hook
hwmon: (ads1015) Handle negative conversion values correctly
